How to disassemble the flashlight

Now the POLICE series lights are very popular, which can be purchased both on the market and by ordering online. In addition to a good flashlight, this device has the function of a stun gun.
How to disassemble the lamp shocker

By issuing a rather loud crash and a visible discharge of electricity, it effectively makes even dogs of impressive size leak.
How to disassemble the lamp shocker

Although the device looks quite good, over time from a fall or from the rapid discharge of the battery, it stops working. In such cases, I want to do something to return the lamp to its former life.
And sometimes it can be done, the question remains, how to disassemble this device to get to its insides? From the outside, this seems rather difficult, as the case looks cast and unapproachable.
How to disassemble the lamp shocker

This article will describe how to disassemble one of these lamps and possibly find the cause of a breakdown.
Since the structural lights are almost the same, the disassembly method is suitable for other models in this series.
It should start from removing the protective tape for fastening screws.The photo shows how to do it.
How to disassemble the lamp shocker

How to disassemble the lamp shocker

It happens that this film itself falls off over time.
So, using a suitable screwdriver, unscrew all mounting screws, both in the front and rear. Usually there are only four of them.
How to disassemble the lamp shocker

How to disassemble the lamp shocker

Then pull the back part, before removing it.
How to disassemble the lamp shocker

There you will see the wires going inside the device, the elements of the charger and a piece of foam for greater density.
Everything has a hinged installation and is rather flimsy. Therefore, be extremely careful not to tear something and make it worse.
Here is a diode bridge, a quenching capacitor and soldered connections, and not insulated.
How to disassemble the lamp shocker

Now remove the front part. We also pull her aside, as with the rear part, and she leaves easily.
How to disassemble the lamp shocker

Two wires are pulled out of it - these are high-voltage conductors, through which electric current flows to the front arresters.
How to disassemble the lamp shocker

Strange, but they are not even soldered, but simply inserted into the holes opposite the electrodes. Apparently even without having direct contact, the voltage pierces the necessary distance to form an arc.
The rest of the front part is essentially a regular reflector. When it is planted in place, the LED falls exactly in the center, appearing as if inside a reflector.
Go back to the back.We pull the bridge with the capacitor as far as possible and extract the high-voltage coil poured into the compound from inside.
How to disassemble the lamp shocker

How to disassemble the lamp shocker

When you pull this coil, two high-voltage wires go from the back side to the inside of the lamp. They need to align, then this procedure will be easier.
As you can see in the photo, these conductors are simply pushed into the inner holes of the housing from the coil to the front electrodes.
How to disassemble the lamp shocker

This is how the extracted high-voltage coil looks like.
How to disassemble the lamp shocker

When reassembling the wire, the thin copper wire attached to them will help. Tighten it will be necessary for the two ends at the same time.
Deal with the back, go back to the front.
We pull out the panel with the LED and behind it we find a block of batteries assembled in one design.
How to disassemble the lamp shocker

They look like micro finger, but have a little shorter length.
How to disassemble the lamp shocker

A total of five of them and they are connected by metal plates, as if welded to their findings.
How to disassemble the lamp shocker

This whole block is placed in a plastic casing.
It has some inscriptions. Namely, the voltage that is six volts and the date of manufacture. It turns out that each element has 1.2 volts, like an ordinary finger-type battery.
How to disassemble the lamp shocker

From this we can conclude that if you want to replace the battery, you can pick up something. The main thing is to put it inside the lantern body.
From battery to LED, the voltage goes through a resistance of about 15 ohms.
How to disassemble the lamp shocker

This photo shows the internal space where the battery should fit.
How to disassemble the lamp shocker

Places a little, but you can pick up something.
You need to assemble the lantern in the reverse order. Given the extremely unreliable assembly, everything must be done carefully so as not to tear the wires and avoid short circuits between them and the housing.

Related news

How to disassemble the flashlight image, picture
How to disassemble the flashlight 51


How to disassemble the flashlight 89


How to disassemble the flashlight 82


How to disassemble the flashlight 95